The Heap. A Gen 2 Tracker/Vitara Build

IdaSHO

IDACAMPER
Bit of progress to be reported...

An interesting combination of tear-down and rebuild going on :LOL:

Not sure if I mentioned it before, but there was evidence of rodents living in this thing...
So I started with an interior gutting, as well as seat tear down.

The seat covers soaked in the shop sink with a purple-power solution for a week or so.
Considering just how soiled they were, they came out pretty darn good.
Assuming they didnt shrink, they should go back together nicely. They are comfy seats.

The rodents it seems had made nests in both rocker panels.
No amount of flushing the rockers with water would do it.
So I cut them open.... what a mess. I removed a full 5-gallon bucket of nest/waste out of there.
As well as expose some rust from all of it.

No worries really, it just means the little tracker will get some rocker-sliders.
Ive got the local machine shop breaking some 1/8" steel sheet for it.
The result should be a slight gain in rocker clearance, and they will be slightly boat-sided as well.
The rockers themselves are just cut open at this point, in order to sanitize this nasty heap.
Final cutting and clearancing will have to wait until I have the correct wheel/tire package.
Its getting 31/10.50's, as well as deeper gears. More on that later....

Finally, did some junk yard shopping.
Drivers fender, grille, headlamp. After some more body work on the inner fenders, things went back together well enough.
Not exactly going for show quality here :LOL:

50708166727_2c00420ed9_b.jpg


50708167527_a6eb14fbb8_b.jpg


50708081266_d122dfae9c_b.jpg


50707347473_3a644300d2_b.jpg


50708080141_077ba9615b_b.jpg


50707346428_2a96c4262a_b.jpg


50708168307_706a335c90_b.jpg
 

Inyo_man

Don't piss down my back and tell me it's raining.
Nice project!

Trackers are great little rigs...my kids both learned how to drive and turn a wrench on a '91 and '94 Tracker. The 5-speed manual is fun to drive and when you dial in the motor they will run like a champ.

Nice work with the winch! Keep the snap shots coming...

Cheers
 

IdaSHO

IDACAMPER
Will do

Some ******** cell phone pics from this evening.

For now, I've got a single full size matching spare rolling, to do all the flex/body tests.
This will be a slow project, so I wont bother buying the full set until things are nearly wrapped up.

They fit better than anticipated. Though there will be plenty of steel to be removed/altered.
The plan is to squeeze these on, without any body or suspension lift.

Going to try the Milestar Patagonia 31/10.50r15 on cheap vision steel wheels.
Originally I wasnt totally sold on going so large, but I did manage to find the deeper gears (5.12's) to match, so here we are.
Stock are roughly 27's, with 4.62 gears. The deeper 5.12 gears will be a nice match for the 31's


50734832111_397712d71f_b.jpg


50734937542_fac31f4b23_b.jpg


50734832101_d55bcc991b_b.jpg


50734937517_50eefc0ac8_b.jpg
 

IdaSHO

IDACAMPER
This wont be nearly as involved as I thought it would.

These are flex tests with OEM struts, OEM bump stop in place, with coil and sway bar removed.
The footwells, and and some of the inner fender on door side will have to be reworked,
the fender tab on the front will have to be shrunk, and the fender opening raised + flares.

No sweat. let the sparks fly. :cool:


50737696467_88dc65a5ce_b.jpg


50737695877_91c224384b_b.jpg


50737588351_48fa21fd9c_b.jpg


50737697727_f463fdfcab_b.jpg


50737589571_0836840811_b.jpg


50736853868_078e7d0c6e_b.jpg


50737700147_f8df92e52b_b.jpg
 

IdaSHO

IDACAMPER
A bit of progress, but not without a casualty.

Lots the rear motor bearing on my 15 year old Dewalt angle grinder...
After determining nobody in town had the bearing, I made a mad dash right before things closed to get a replacement.

No worries, once I get the $9 replacement ebay bearing, Ill have two POS dewalt angle grinders to beat on!

50756889756_67ecbc95c8_b.jpg


Anyhow...

After a bunch more cutting and grinding, my two-piece, slightly boat-sided, rocket panels are gong back in.
I had these broke into shape at the local machine shop out of 12ga cold roll.

'nother ******** cell phone pic

50756154138_543deeeb2f_b.jpg
 

IdaSHO

IDACAMPER
Not a whole lot to report.

Im slow.

But I have progressed more into putting steel back onto this thing.
That feels like progress :oops:

Both rockers are fully welded in, and we are moving onto patching the gaping holes in the inner fenders now.

I have also introduced myself to clecos
Fantastic little buggers
They will help this amateur body guy sort out this sheet metal mess. :ROFLMAO:

50773361252_0bfe7ea922_b.jpg


50773360917_084b94dbb5_b.jpg
 

IdaSHO

IDACAMPER
Inner fenders fitted and welded in.
Just cheapo rattle can primed for now.
Once the body come off all will be blasted, seam sealed, undercoated, etc.

Tires still clear, but it does lok like I might have to rework the clutch pedal arm a bit, it hits the new sheetmetal :ROFLMAO:

50788667052_46cc6e4b44_b.jpg


50787802488_6a551a611e_b.jpg


50788555321_78dde21ee3_b.jpg




Fenders trimmed and rehung.
Next up is the rear inner fenders.

50788668677_b680485b28_b.jpg


50787804453_e9e0462ba1_b.jpg
 

IdaSHO

IDACAMPER
Well, I was making decent progress with the rear inner fenders, until the fancy chinese Harbor Freight flange/punch tool quit workin'
So I changed gears and started on the front end with the winch tray.

We should be under 3,000lbs once done, and to keep with the light weight theme, a cute little 4500lb ATV/UTV winch is being fitted.
With some extensions and a block it should do just fine. Amazon special, with a gift card, it was just $55 :ROFLMAO:
Pretty sure its the same 4500/5000lb unit that everyone (including badlands) is rebadging.

A couple of brackets will be welded to the frame horns, then the tray w/winch will be bolted in.
The front will be finished with a simple, custom tube bumper.


50821897043_2c175c1cd1_b.jpg


50822647201_6733d95a78_b.jpg


50822647291_773d2b702e_b.jpg


50822742222_e2af33ecb5_b.jpg
 

IdaSHO

IDACAMPER
Awesome part of about such a project, that has so much on the list to do, I can pretty much just pick part of the car to work on and be productive :ROFLMAO:

Also a good thing Im in no hurry.... 'cause Im slow.

I played with 1-1/4 SCH40 black pipe and the cheapo harbor freight tube cruncher today.
Made decent progress. The roundy round of this Gen2 is a bit tricky, but Im liking where this bumper is going.

Slim and trim, it follows the contours pretty well.
Just have the wings to tie together, recovery points, and tow-bar points to work out.
I think Ill relocate the little winch fairlead to the bumper as well. Placement of the lower tube just isnt the greatest.
But I dont want to loose any more clearance.

50846489673_83fc0818f9_b.jpg


50847298982_ba84b5cc1b_b.jpg
 

oddball4x4

New member
Doing awesome work with this! When my Tracker gets retired into a play truck I may have to copy what you did with the wheel wells.

I'm very interested to see how the front bumper turns out! Most the bumpers that I see for these trucks are boxy and just don't match the style very well. did you use a tube roller for the large curve that cover the center part of the truck? or was this a piece of steel that you are reusing and it just so happened to have the correct curve in it already?
 

IdaSHO

IDACAMPER
No tube roller, and no pre-bends.

All was done with the Harbor Freight bender. Just took time, as you have to go slow to do long continuous smooth bends. (y)
 

beanco

Member
remove this bolt 10 extra horsepower :LOL: makes a difference


03154B45-04E7-4DA1-AD5A-FE318F27FDA0.jpeg

great work with the pipe kinker.Love trackers and sidekicks.
check timing chain and make sure cooling system is working properly.
Ben
 

Forum statistics

Threads
185,533
Messages
2,875,610
Members
224,922
Latest member
Randy Towles
Top