Santana/Defender 110 Overland Build Cummins R2.8

spikemd

Explorer
Drivetrain in place! Welded in motor mounts and fabbed up tranny mounts from 300tdi cross member. Will weld in cross member now that everything is in place. Looks like 300 tdi driveshaft will fit which are the same length. Dront of engine will get cleaned up as u can see a bunch of surface rust. Need to work on suspension and axles now...

20180416_111048-1664x1248.jpg20180416_112946-1664x1248.jpg20180416_122407-1664x1248.jpg20180416_164233-1664x1248.jpg20180417_154821-1664x1248.jpg20180418_102436-1248x1664.jpg
 

spikemd

Explorer
Working on wiring harness. Looks like only 4 wires needed to connect to main wiring - ignition, oil pressure switch, alternator and coolant temp sensor.
 

spikemd

Explorer
Modifying frame for front suspension. Keeping radius arms with 12 inch coil ovwr shock setup. Testing full compression and extension. Camber correcred radius arms very close to the frame.

20180604_163944-2080x1560.jpg20180604_163927-2080x1560.jpg
 

getlost4x4

Expedition Leader
Looking good.

Do you think it would have been easier to just import a Defender body and frame and then put it together in the states? I've been thing of thinking about going that route. Import the frame first. Then the drivetrain and the frame.
 

spikemd

Explorer
Without customs paperwork for the vehicle there is no way to register it. The Santana by itself was in great condition but I want a more robust overlanding vehicle. I would be changing out the axles and upgrading engine anyway. In retrospect, I probably shouldve bought the cummins I wanted since I have spent a lot of time and money upgrading the 300tdi.
 

spikemd

Explorer
Sand blasted front covers and painted them. New pulleys, tensioner, water pump, thermostat and housing, fuel lines, lift pump.
 

Attachments

  • 20180604_163910-1560x2080.jpg
    20180604_163910-1560x2080.jpg
    665.4 KB · Views: 31
  • 20180607_123149-1664x1248.jpg
    20180607_123149-1664x1248.jpg
    636.7 KB · Views: 33
  • 20180607_123137-1664x1248.jpg
    20180607_123137-1664x1248.jpg
    492.1 KB · Views: 31

spikemd

Explorer
Attached covers and front of engine. Tightened up crank pulley to massive torque (60ft lbs plus 90 degrees).
 

Attachments

  • 20180608_170216-1664x1248.jpg
    20180608_170216-1664x1248.jpg
    426.6 KB · Views: 37
  • 20180608_174649-1664x1248.jpg
    20180608_174649-1664x1248.jpg
    383.2 KB · Views: 38

spikemd

Explorer
We found the right front end of the frame had a crack in it amd needed repair. We also wanted to extended the frame out a bit to allow more space for the grill, winch and AC.

Cut...grind...weld...repeat...
 

Attachments

  • 20180607_175225-1664x1248.jpg
    20180607_175225-1664x1248.jpg
    491.5 KB · Views: 60
  • 20180608_134121-1664x1248.jpg
    20180608_134121-1664x1248.jpg
    375.3 KB · Views: 62
  • 20180608_134115-1664x1248.jpg
    20180608_134115-1664x1248.jpg
    310.9 KB · Views: 62

spikemd

Explorer
Been awhile since an update.... We have rear suspension axle over leaf in place from Ruffstuff. Gives us 6+ inches of travel which might be too much. But with full exocage, rear drawers, 75quart fridge and build out, another 1k pounds is conservative. We'll see how it settles out. We can cut the perches down a bit or have the springs re-arched once it is loaded down.
 

Attachments

  • 20180612_094417.jpg
    20180612_094417.jpg
    3.7 MB · Views: 52
  • 20180614_170949.jpg
    20180614_170949.jpg
    1.5 MB · Views: 55
  • 20180620_195051.jpg
    20180620_195051.jpg
    3.7 MB · Views: 55

spikemd

Explorer
Front suspension required some major fabrication. Used outfitters from another defender for the castor corrected radius arms. Cut and welded new lower mounts for 14 inch coil overs.20180824_194147-1040x780.jpg20180825_173234-1040x780.jpg20180824_194629-1040x780.jpg
 

Forum statistics

Threads
185,535
Messages
2,875,628
Members
224,922
Latest member
Randy Towles
Top