Jeep XJ Pop Top Camper Build

ed2efb10b90d08f2a1d696d7bf093ae0.jpg
4e3a57d45ab6747800e1f021a46c9dfa.jpg
e4672dedb257f743fd5f532f1c83d7e0.jpg


Built a couple mock up Hotwire cutters. PVC and lightweight steel tubing build warped too much to hold wire tension. Not going to use any of my good steel material in the garage...

Follow (Instagram) --> @craftsmancollaborative
Subscribe (Youtube) --> @craftsmancollaborative

2x3 worked well enough for this use.
Steel angle on each side to hold the tensioning bolts. Two 18v power tool batteries in series with a switch. One 18v worked decent but not enough power to cut even. Need to get some heavier duty tension wire to hold up with the added heat. Then we’ll be in action.
 
Last edited:
7f31b6be64467dc415ac419527153f40.jpg

.031” music wire from the specialty hardware shop in town (Marshall’s) held up much better with the two-battery Hotwire.

007df958fb83f66ffea12bde916cc3aa.jpg
cf4c8c4b94f38d609c776aeaf6269ee5.jpg
b26b6e03db13481d47411627635e558f.jpg


Blind chopping didn’t go so well and began to burn into the “stringer” wooden structures. Went back with a coarse file and dug down so I could see it follow the wood profile.

764d7d3dd7d5955d43f68cf70250b9cb.jpg


Hotwire went well. In place of one long major cut I removed several smaller sections.

c563b423c05c54e0bcc8c3b23d111f04.jpg
eeba866fac4342172ec21caf59123f32.jpg
 
d9dd601f49f535668129a40c56e4b6dd.jpg

49d3f55a0cff06407ed7b620d035d998.jpg
831515e6909b2d5d09170642da71c3ed.jpg


Taking a couple days of finer sanding work to finesse the shape and think it over to make sure I’m happy with the profile.

I’m at the point of starting other projects as a break from my current projects...
wrenched on the bike a bit today and tore it down to do some pre-season work. Good to give the mind a Jeep break but stay active mechanically.

Follow (Instagram) --> @craftsmancollaborative
Subscribe (Youtube) --> @craftsmancollaborative

15e2a2534c178148515240797821e105.jpg
 
Last edited:
0ef9effffb1e536d9d077f607f79543f.jpg
d435b26d1f260439d7804be20b148931.jpg


May have changed my mind on the direction of the fiberglass build, we will see. My current thoughts would require more prep and as such I sanded down the full assembly.

Side note: the rear plug profile was intentionally built to be easily removable and adjustable. Came off in a matter of 4 screws and a light pull.
 
Last edited:
538796f2df1ff7747093332265444ffd.jpg
59bb52107a73724966fc4a1bd40be943.jpg


Weld cracked through on the exhaust manifold. Summit is supposed to warranty it and applied the credit towards a new Gibson header.

Didn’t want to buy Chinese twice and welds look much better on the Gibson. Works well with the high flow magnaflow catalytic and flow master. Picked up the ceramic coated model as well.
 
7016554c2e46ce96db9634d05a51d39c.jpg


3863f15444b720b91fac605a97e7e3cf.jpg


Getting back to the camper top plug & mold. Measured out the rain gutters within a 1/16” tolerance and built up a frame out of 2x3 to hold it in these exact dimensions. Open-ended fiberglass profiles like to flop.

The makeshift sawhorses were far too wobbly at this point so reinforcement came to them as well.

Still need some bondo work.
Need to buy/borrow a 20-30gal compressor to run the spray gun.
Next stage is primer, final sanding, waxing and then mold making.

fba318aad3b08bd70345b88f7b5b2bd1.jpg
 

ram2500_24v

New member
Its too bad that the Gibson header does not come with any expansion joints like some of the other brands do. I also think that the Cherokee/Wrangler exhaust systems should have a woven stainless flex joint some where in the exhaust piping to allow for movement when the motor torques under load.
 

Put out a video on the header install. Goal is to start pushing the Jeep build more regularly on that platform. Be sure to subscribe for the in depth pop-top video I’ve been working on.

Of course, I’ll post here too when that series is live.

In other news I picked up an oiled 30 gallon kobalt air setup today for the mold primer and gel coat. That thing is quiet! Should be just enough air volume for my home shop setup.

Follow (Instagram) --> @craftsmancollaborative
Subscribe (Youtube) --> @craftsmancollaborative
 
Last edited:
529b7df956d1bafd3e9191d7bd8f378c.jpg
6dad8f0b2877024b717265e180a8b892.jpg


Put together the soft top real quick in case we get some rain anytime soon.

Work slowed on the top, taking extensive time in the bondo stage to ensure all is even and the profile I want. Almost a gallon of putty in, so the profile will be a good bit smoothed out and a little different from the original Westfalia shape.

At this point I think I could have made a scratch plug out of foam for about the same hours, as it sands much quicker than bondo... it is nice to have a base shape to draw off of though. I’ll post when I have some more exciting news.

Follow (Instagram) --> @craftsmancollaborative
Subscribe (Youtube) --> @craftsmancollaborative
 
Last edited:

Forum statistics

Threads
185,530
Messages
2,875,570
Members
224,922
Latest member
Randy Towles
Top