Jeep XJ Pop Top Camper Build

4958596962151dc890e2fd8db9e09180.jpg


Touching on the other areas of my build, here is my one ton steering setup on the cherokee. It is the cavfab OTA trackbar and alpha Steering Kit. Has a new mount welded on the axle trackbar side. Runs a Currie Johnny joint to a RE frame trackbar bracket on the other end. Also have the cavfab short arms installed. Beefy, killed the majority of my death wobble, and they have a “no bs” warranty they already honored for a failed builder part.

Since that picture I changed the draglink to run under the pitman arm and that eliminated the little bumpsteer the XJ had.
 
Last edited:
Found some more builds that give a good insight into the poptop process.
First of all, some of the suburban guys adapting their own diy system here.

^Interesting take on a full DIY top from the fiberglass to the hinge system.
Especially the Cantilever system with the electric actuated component.

Also, found an extremely detailed build of both a fiberglass pop top mold and the finished shell on a 3500 EB Chevy van Here.
Really clean top, and better than even some production runs I've seen.
Opens up the possibility to recreate the top many times and custom fit the vehicle.
 
Last edited:

msimmo

New member
2nd link is the same as the first, I would love to see the E350 top. Awesome build, getting inspiration for my comanche.
 
Last edited:
4ec9aa6552558f2648bc02965ee97b27.jpg


Pulled the top again today and started on the edge profile for the roof chop. See the difference from the original temporary cut and fold I did below. Down below will be a fullsize sleeping platform so having the entirety of the roof cut will give the roomiest Jeep camp setup possible.

Many have asked why I don't build a loft up top instead to function like a rooftop tent setup. For this build, I wanted the ability to sleep in the lower cab of the Jeep when needing to stealth camp or when the weather is particularly rough and windy. If you've ever been in a rooftop tent while Jeep Camping in a windy exposed landscape, you know how rough of a night that can be.

1136526172bcef9b3195ca0fa8dc0740.jpg


I used some 1”x1” angle steel plate. The length was 73” as pictured and cut a slot further forward in the roof for it to sit flush. Once I get more material I’ll wrap the whole roof edge of the cherokee like this, and devising a system to mount the hinges straight to it and be able to remove them easily to run topless.

faa54f0fda90097b20aaf8c01c87d318.jpg
608a2d018145d647a172831b532cd840.jpg


The flat bar sits pretty well among the back 3/4 and lines up over the factory roof rack mounting points. I cut off the rack nutserts and spot welded it all in place for now. The front 1/4 needs bent with clamps to fit the curve up to the windshield.

Looks way better in person compared to the old fold method.
 
Last edited:
6fcd9af1710b224ec0964f9908db7ba7.jpg


Tacked up the front hinge brackets today, and test fitted it all to be sure of fitment.

The original hinge’s lower mounting point (to the car) sits on the outside of the hinge itself, but I welded a new piece of 3/4” bar to stick out the other way. This will provide easier access from the cab to quickly remove the top, and also allow me to have the perimeter angle bar to mount the canvas, without having to run it underneath the hinge.

7ccf44ddb59394d0d35ec8083af843f5.jpg
e572b0f56179ccd9cf971cb7f2bd2e6c.jpg

fa0db551ad6545b82275b9f4895b4814.jpg

215a14936196f0858f49efd4c26bcc1d.jpg

3c39fe9f73dd99f2d357d85dd453737d.jpg

b8ec33764236d8f7efd42b1c78285c59.jpg
 
Last edited:
As I'm progressing on renovating the camper concept, taking into account long run interior concepts and modifications for travel and living comfort.

I've removed most all the rattles by fixing the dash and removing loose interior plastic panels, but the lift gate bounces like crazy.
Anyone have any experience adding an additional seal, latch, or otherwise idea to eliminate this? Drives me crazy heading up the trail to camp.

I will pick up some new screw in "bumpstops" to see how much of a difference that makes, but as of now is the only part of the body constantly bouncing/moving.

Also threw code P0740 (torque converter clutch circuit) again today, throws it occasionally and seems only when doing a lot of errands around town, stop and go and once heated up. AW4 Trans runs fine, fluid levels proper, any idea on heat affecting solenoids or wiring as a possibility? Insight appreciated.

Picking up more material from IMS tomorrow and then will finish the passenger hinge and rear push-bar brackets.
 
Last edited:
Are you planning on making a sleeping platform up top or just using the pop up for standing room?

Still unsure on this. The lower will definitely have a full-time full-size bed. This holds the advantage of more head room with the top up, and the ability to still stealth camp comfortably with the top down. It'll also be able to avoid wind and rough weather limitations of a roof top tent where many Jeep Camping setups fall short.

I have a hammock/cot concept or to do something like the GFC Tacoma platform, but really don’t see a point except for hot nights or sleeping extra visitors/friends?

Sleeping on the lower with the top up feels overly roomy.
 
Last edited:
251d022e6a0b730e8c76fdce1d67070e.jpg


Stopped in the metal supply this morning and got the remaining material for the roof edge lip. The cherokee took two 10’ angle steel to run the perimeter. IIRC it was 73.25” long and 44.75” wide.
9e57b298025aaf25ee8d556084cce762.jpg
1f9f6370e63760ec86ba8bc0c5510af4.jpg

Lining it up wasn’t too bad, just took time and patience with the clamps. Forgot how much I dislike flux core welds though... exchanged my empty 75/25 mig cylinder for straight argon to use with the spool gun and in the meantime have flux for everything steel.

53b3cc7ed0fac1de4330df81859bf10a.jpg

The rear was the hardest section to fit. The front surprisingly went ok, but bending the angle to the curve of the rear took a good minute. Didn’t help that where I needed my clamp to sit was along the rear joint of my cage. Figured it out eventually and had to run the full inch weld right away as the spots would snap by the time the clamps started slipping. Now is fitted nice along the curve.

Test fit everything once again, then run stitch welds into the body and go around with seam sealer to fill the remaining gap.
7f9522de58278adc4992141b2627042d.jpg


If I were working on someone else’s rig I think I’d just go ahead and rivet the edge frame into place like a lot of van conversion shops do along with rtv. Think it would be better than worrying about welding thicker metal to the roof.
 
Last edited:

jeepdreamer

Expedition Leader
Another option for more interior space is to reshape the floor. I ran a t-case drop on mine so the tranny hump rear of the front seats and the back seat "well" area all got removed. Enough area is created to add a good size water tank or ???

d0ff516b1eef04d63274f27a4536b8cc.jpg
66288f4374fb05b36ca5c2b6d21f7d4e.jpg
58cc6a9de624eb3f2365c8d1d2030c30.jpg


Just an idea I thought I'd pass along.
 
Another option for more interior space is to reshape the floor. I ran a t-case drop on mine so the tranny hump rear of the front seats and the back seat "well" area all got removed. Enough area is created to add a good size water tank or ???

d0ff516b1eef04d63274f27a4536b8cc.jpg
66288f4374fb05b36ca5c2b6d21f7d4e.jpg
58cc6a9de624eb3f2365c8d1d2030c30.jpg


Just an idea I thought I'd pass along.

Stop!! Don’t tempt me to chop my body more until I can finish the current project

Nice work though, I was thinking about relocating the ebrake adjustment bracket along the drive side of the Floorpan and putting a 4 gallon rectangle water tank under there with a belly pan to keep the interior open.
 
Last edited:
Another option for more interior space is to reshape the floor. I ran a t-case drop on mine so the tranny hump rear of the front seats and the back seat "well" area all got removed. Enough area is created to add a good size water tank or ???

d0ff516b1eef04d63274f27a4536b8cc.jpg
66288f4374fb05b36ca5c2b6d21f7d4e.jpg
58cc6a9de624eb3f2365c8d1d2030c30.jpg


Just an idea I thought I'd pass along.

Just crawled under the jeep and actually seriously considering this now.

How hard was it beyond taking the time to bend the new floorpan and fit it all in place?
Any issues with driveshaft clearance when the rear suspension is fully compressed?
My bed platform will sit over this regardless, but that’s a good bit of storage for this size camper
 

jeepdreamer

Expedition Leader
Just crawled under the jeep and actually seriously considering this now.

How hard was it beyond taking the time to bend the new floorpan and fit it all in place?
Any issues with driveshaft clearance when the rear suspension is fully compressed?
My bed platform will sit over this regardless, but that’s a good bit of storage for this size camper

It was actually a lot easier than you'd think. Relocating the charcoal cannisters was a small pain but driveshaft never came near anything.
cb8e5913c1ebbcd5fa3b199e0cd9a4ed.jpg
 

Forum statistics

Threads
185,531
Messages
2,875,592
Members
224,922
Latest member
Randy Towles
Top