Cummins Canoe (A Stepvan Story)

PlethoraOfGuns

Adventurer
While we wait for transmission parts, some other things can be done. The heater box was looking a little rusty, so time to look at that. It all works great, but rust is like cancer. Once it starts, it grows fast and can quickly become overwhelming. I wanted to just scrap off the peeling paint with a screwdriver and hit it with some spray paint, but I'm sure glad I didn't! I hate taking shortcuts and this was such an easy project!

IMG_20200823_104820 copy.jpg
Yep, this thing was looking pretty rough. The heater core is located inside this box, forward of the firewall. The blower is inside the cab.

IMG_20200823_111052 copy.jpg
Now on a normal car, removing the heater core can take upwards of 8 hours to remove and the reverse to reinstall it. This one took about 10 minutes to get out of the vehicle. I love this thing!

IMG_20200823_111101 copy.jpg
Very simple, no fuss design.

IMG_20200823_112456 copy.jpg
Oh boy...

IMG_20200823_115507 copy.jpg
Oh no...

IMG_20200824_095759 copy.jpg
Lots of sanding and a light acid bath and all the box pieces are good more paint.

IMG_20200824_124451 copy.jpg
Had some extra time so we reinstalled the rear bumper.
 

PlethoraOfGuns

Adventurer
Since the axle is all back together, it would be a good time to get the fuel tank back in the rig.

IMG_20200826_100553 copy.jpg
Got the tank all cleaned up and painted.

IMG_20200828_103208 copy.jpg
The fuel sending unit crapped out about 11 hours into the ride home when we bought the vehicle. So in goes a new fuel sending unit. Hopefully this does the trick. If this wasn't the issue, who cares. The 40 gallon fuel tank was down and out, just change the sending unit ya dummy!

IMG_20200829_135428 copy.jpg
Got these nice new tank straps from NAPA! Even had the right size the first time. Found these strap rubbers as well. Gotta protect the tank from future rubbing.

MVIMG_20200829_160007 copy.jpg
This new model tank jack works great too!
 
Last edited:

PlethoraOfGuns

Adventurer
Transmission parts came in the mail!

IMG_20200828_104302 copy.jpg
These are all the components we think we need. Emphasize on the think part.

IMG_20200828_105748 copy.jpg
Pretending I know what I'm doing.

IMG_20200828_110135 copy.jpg
These springy thingalings looked important on the parts diagram, so they go in too.

IMG_20200828_110341 copy.jpg
Got a new ringading funny ring to put in. Note the chassis paint that is still on my thumb. This stuff is never going to come off.

IMG_20200828_121600 copy.jpg
Had to drive this drift pin in to secure this black shift fork to this shift rail. Only problem is that the silver shift fork is in the tail section, and the black shift fork is in the main case, down where you can't get to it very easy. And I was by myself, and it was awkward, and I just couldn't get it all lined up. That was, until I applied marked lines on the shaft!

IMG_20200828_124030 copy.jpg
With the lines on the shaft, I was able to align things properly and get the pin in no problem.

IMG_20200828_125616 copy.jpg
Good news is that all the components we ordered actually went in somewhere. No spare parts laying about!

IMG_20200828_185223 copy.jpg
Some RTV sealant and wrenching and all back together!

IMG_20200902_112625 copy.jpg
Fill plugs are too much of a pain. You never know where they are and if you do they are usually covered in grease and grime. This is a much more effective way to fill your transmission with gear oil. I will also add the awesome fact that I tore apart this transmission and modified it while standing next to it, while it was still in the vehicle. Try doing that in your regular van or pickup truck!
 
Last edited:

Bikersmurf

Expedition Leader
Transmission parts came in the mail!

View attachment 614547
These are all the components we think we need. Emphasize on the think part.

View attachment 614548
Pretending I know what I'm doing.

View attachment 614549
These springy thingalings looked important on the parts diagram, so they go in too.

View attachment 614550
Got a new ringading funny ring to put in.

View attachment 614551
Had to drive this drift pin in to secure this black shift fork to this shift rail. Only problem is that the silver shift fork is in the tail section, and the black shift fork is in the main case, down where you can't get to it very easy. And I was by myself, and it was awkward, and I just couldn't get it all lined up. That was, until I applied marked lines on the shaft!

View attachment 614552
With the lines on the shaft, I was able to align things properly and get the pin in no problem.

View attachment 614553
Good news is that all the components we ordered actually went in somewhere. No spare parts laying about!

View attachment 614554
Some RTV and wrenching and all back together!

View attachment 614555
Fill plugs are too much of a pain. You never know where they are and if you do they are usually covered in grease and grime. This is a much more effective way to fill your transmission with gear oil. I will also add the awesome fact that I tore apart this transmission and modified it while standing next to it, while it was still in the vehicle. Try doing that in your regular van or pickup truck!
Absolutely no way in an E-series van... everything on them is like pulling teeth without freezing.

Keep them coming.
 

PlethoraOfGuns

Adventurer
Awesome and great story telling.

Thanks! Hopefully this thing gets finished and the real story begins.

Absolutely no way in an E-series van... everything on them is like pulling teeth without freezing.

Keep them coming.

Oh my. I've worked on them Fords before. They are pretty bad. But the Mercedes and Dodge Sprinter vans take the cake on repair and access nightmares. If I had to change a heater core in a Sprinter, I would just scrap the van, haha. We went with simplicity and longevity on this van. So far, it's working out great.
 

PlethoraOfGuns

Adventurer
Can't wait to drive this thing and see if all our work on the axle and transmission actually worked and won't blow up! In the meantime, got more stuff to reassemble.

IMG_20200829_104417 copy.jpg
Heater box all painted and back together.

IMG_20200906_115318 copy.jpg
Redid the whole blower box too.

IMG_20200829_112844 copy.jpg
Yes, maybe we should have changed the heater core when we had it apart. But it was working great! And the best part, it only takes 10 minutes to remove! So not an issue if it ever needs to be replaced.

IMG_20200730_093451 copy.jpg
This shock mount isn't looking so great. It's probably been broken for awhile since one of the bolt holes is not so round anymore.

IMG_20200730_093458 copy.jpg
Kinda supposed to be like this.

IMG_20200730_094828 copy.jpg
This was not fun to clean and prep for welding.

IMG_20200905_192744 copy.jpg
But it will work.

IMG_20200906_162530 copy.jpg
All welded and painted. Van has all new shocks now!
 

Attachments

  • IMG_20200730_093451 copy.jpg
    IMG_20200730_093451 copy.jpg
    2.7 MB · Views: 24

PlethoraOfGuns

Adventurer
Great news, the van is mobile! Everything works and it drives fantastic!

IMG_20200914_115805 copy.jpg
This thing cruises on the highway! Gained 15mph with functioning overdrive. Much quieter too. Still hurts your ears, but no more bleeding out of the one ear.

IMG_20200907_101637 copy.jpg
Oh boy, weeks sitting in one place made a nice mess. Lots of rust and other stuff.

IMG_20200904_160838 copy.jpg
These bracket things gotta go. Thinking skinning the whole interior in plywood.

IMG_20200904_161714 copy.jpg
Not quite sure what these metal brackets are for, but they are going also. We have better ideas for some sort of divider wall between the cab and the living quarters.

IMG_20200904_163135 copy.jpg
Doing the old notch and chisel.

IMG_20200904_171104 copy.jpg
Doing more gutting, looking at this weird tube thing. No idea what it is.

IMG_20200904_171055 copy.jpg
Any ideas what this thing is?
 

marret

Active member
Awesome. No idea what the thingy is, but it looks well damped for vibration. End caps must come off.
 

PlethoraOfGuns

Adventurer
Son of a sailor. This whole time I've had my documents inside a small backpack just thrown in the back corner. Ok then, this makes perfect cents. We're keeping the document tube then.
 

Forum statistics

Threads
185,530
Messages
2,875,576
Members
224,922
Latest member
Randy Towles
Top