72 IH + ‘85 Alaskan = Questionable Judgment...

Nailhead

Well-known member
Nailhead,
I have 2 more of the horizontal propane tanks like yours. You can have them if you ever get up to Casper.

Thank you!

Can they still be refilled, what with the POL valve instead of the OPD?


Sent from my iPad using Tapatalk
 

Nailhead

Well-known member
That was a lot of interior pirelli seal replacement!

Haha seriously though, great work!

Tapatalk sent error messages three times when I tried to post that, and apparently posted it anyway.

Thank you for the compliment!


Sent from my iPad using Tapatalk
 

fisher205

Explorer
Thank you!

Can they still be refilled, what with the POL valve instead of the OPD?


Sent from my iPad using Tapatalk
Supposedly they can because they are ASME bottles. But some of the people refilling them may not recognize that. I got them with my first Alaskan. 2 Alaskans later, I still haven't used them. They were originally to be mounted on the inside wall of the bed on each side of the wheel well.
 

kerry

Expedition Leader
I have that style of tank in my Northstar. They can be refilled but some bulk fillers are unaware of that and might refuse you. New Horizontal tanks with the updated threads cost about $115 last I checked.
 

Nailhead

Well-known member
Next task was vent replacement. The old ones were broken in various annoying ways, so they had to go.

I got my staging set up, and found that my extension plank wouldn’t fit on the top of the ladders because of the hinge rivets, and the next rung down was too low.

I tried airing the tires down, but I found one valve stem too close to the rim to accommodate my air chuck, so I gave that plan up.

This isn’t sketchy-

bc90f4382d33a714e9124474116387d9.jpg


54d3c66b1cb64bc1045a920c895ae315.jpg


072516c3bea844dbdd0087f3e9894001.jpg


Time to proceed.

Got the vents & butyl strip:

e6d2035a298b933dc5825ae2968db1b4.jpg


The first vent was pretty easy, just undo the screws, carefully pry it off, and clean the sealing surface:

d258b27b402b1b6464cf0ffe97780cf4.jpg


8aabbd633151438fc349d6f9034d71c5.jpg


Next, I stuck the butyl tape to the vent flange, and set the vent:

8567248942e61d04b9d81fba21eee252.jpg


Then I ran the screws in & finished it with a bead of rubber sealant. I would have liked to use stainless screws, but they’re a relentless PITA in a magnetic bit.

Move to the front, repeat...

082db451fb59a60d8cb225f616e4600b.jpg


...right?

Not really-

0ba2148f4bb38ce71327ba38daf7effa.jpg


I was greeted with this mess when I pulled this, an apparent replacement vent. At least I had somewhere to rest my feet so I could actually sit while I scraped that silicone off-

b9835e820452e3a5de7c1b95553c2e5f.jpg


My knees were really beginning to hurt from kneeling on that plank.

Got it after while:

cab62ea9f8176d76321f135899c3c0cb.jpg


Victory...

f8f556be68040e9f9fbe5de3b68dc295.jpg


Finish it with the “garnish”:

b311596104494562a73bfbaf5d31ec7b.jpg


Oops—

21783b06bd16f318e7c2bb56293a7b46.jpg


And another item checked off the list.


Sent from my iPad using Tapatalk
 

Nailhead

Well-known member
Then I took time out to reacquaint with the motivation behind all this work:

b2d54de80cc6221f825c82de6b880c79.jpg


I’m sick of towing and sleeping in that cargo trailer.


Sent from my iPad using Tapatalk
 

Nailhead

Well-known member
A few weeks later, I borrowed my buddy’s 6” gutter trailer, and bought the IH hood back to paint it:

18b32989d4dfe12fb779aed3351631ff.jpg


After a wash, I undercoated the inside:

0582b106fc0f43548928b2e9598751b6.jpg


d1ceb3ca5efebd5137aedf8172c1f405.jpg


And unearthed a relic of its past while sanding:

011390e30ad6716300a6937211b709ee.jpg


I googled that, and found it’s in Centerville, AR. I also found they’d misspelled “Galla”. Oops.

Done:

2ff8eac6d66b367f1f2c838e31bb1d6e.jpg



Sent from my iPad using Tapatalk
 

Nailhead

Well-known member
On to addressing what I considered the biggest problem this camper had: cabover deflection. Previously, when I would climb into it to raise & latch the cabover panels, my weight would deflect it downward to the point I couldn’t lock the panels open if I kneeled more than one foot from the inside edge. Not acceptable, and a little scary, if I’m honest.

I talked to Brian Wheat at Alaskan, and he mentioned this was pretty much the first design change his dad implemented after removing purchasing the company in the ‘80’s. His suggested installing 4x4 steel angle channel at the front corners of the lower section, so I bought these:

1ca85d889369ad21f547d1e8d61fdf70.jpg


4x6. I like overbuilding certain things.

Here’s where they’ll go:

c47c4ddf029cba16535ca03b26e12ae0.jpg


I had to cut them to fit that luxurious plastic trim:

c18cf04dbeb68469b258003a1ac48204.jpg


And then the mounting holes had to be drilled:

baa97e88b24c0c547901abd8859edbfb.jpg


e4038b46464bd82e6c6f384839def0cd.jpg


And those were just the pilot holes. I went through two 5/16 bits to get them to their final size.

At this point, work on these came to a two-week pause because I needed to weld on extension tabs to accommodate a mounting hole for the carriage bolt seen in the second pic from the top.

FF, and time to mount these to the camper.

Drilling the holes in the sidewall seemed like the best place to start so I could the hole in the extension tab located correctly:

838324ad4276537e4d3b16e60250abcc.jpg


I marked that with the drill:

31a82f494e94566acd5d07da526c50a1.jpg


After repeating this process on the driver-side, I made them look decent:

b2068abd14818ba049301621d952ad9e.jpg


7c745980dc03c506aa3047b54a59a5c3.jpg


A bunch of carriage bolts, a couple grade-8 hex bolts, and some good luck later:

674d72fa9828254e09f25bb15e87edf5.jpg


a87674e6aa00ee1ee81ace0463cab69d.jpg


And cabover defection is largely eliminated. The difference is amazing, and well worth the time & money ($60+-) expended.


Sent from my iPad using Tapatalk
 

Nailhead

Well-known member
It’s October ‘20 at this point, and I decided I’d test the gas plumbing I’d relocated because the day was chilly, and I wanted bask in the heat of that furnace:

01753cd92cd94ddf4820a5d41c84138e.jpg


After 15 or so minutes:

2a6924fefce69139c7d7d9744a94da1e.jpg


Works for me, no more freezing my ass off.

Stove worked nicely, too:
9d48040627f086523e1e6b09bc02a670.jpg



Sent from my iPad using Tapatalk
 

Nailhead

Well-known member
The next project was getting that camper from here to Wheatland where the IH was.

First order of business had to do with this ratty little piece of steel:

211dde4e33036cb7007e2d1de5a0d680.jpg


This is supposed to limit the downward travel of the upper camper section when it’s attached where it’s supposed to be on the back corner angles:

7611743a4ccaba90ed78fe9814174bef.jpg


f657f54ef26eaac8337c4038e6336780.jpg


Bryan Wheat at Alaskan told me these are essential, and not to roll without them to avoid damaging the lift rams. Since the weather window for a trip north was closing (snow expected late the next weekend, and once the roads get salted, the M715 is done for the season), improvisation was in order:

f5da68e341017e92f32a42f2a092792a.jpg


565e74dca6fb813a6a6c57fe1aa8b7df.jpg


8ff43f3623a36abcfd5eed127a25668a.jpg


Worked great, time to go.


Sent from my iPad using Tapatalk
 

Nailhead

Well-known member
After five hours at 45 mph MAX, I made it to Wheatland:

5440fa7013b3fe2fb235c24fdee46541.jpg


I thought this looked cool:

f829f768e841b1b129bfe8e1e050e7e0.jpg


An hour later, the blizzard started, and we hit the road south. Hard.


Sent from my iPad using Tapatalk
 

Forum statistics

Threads
185,527
Messages
2,875,541
Members
224,922
Latest member
Randy Towles
Top