Search results

  1. ccperkdog

    Introducing the “NEW” Alu-Cab Canopy Camper

    Could you maybe get a hose in there connected to a wet/dry vac like Shopvac? I also would love to hear what everyone with the water tank is doing for maintenance. I drain it as much as I can, on a reverse incline, if I’m not going to use it for a few weeks. But more often than not I find myself...
  2. ccperkdog

    Introducing the “NEW” Alu-Cab Canopy Camper

    Managed to fit a skateboard to a side panel without needing to change out the struts (for now). 18” perfect bungees fit the existing holes in the aluminum frame in the door.
  3. ccperkdog

    Introducing the “NEW” Alu-Cab Canopy Camper

    Thanks! It’s going to be a longboard skateboard on the underside, but same weight as a pair of Maxtrax.
  4. ccperkdog

    Introducing the “NEW” Alu-Cab Canopy Camper

    Anyone who has changed out the gas struts on the side panels to support more weight have a part number?
  5. ccperkdog

    Introducing the “NEW” Alu-Cab Canopy Camper

    Question for those of you who upgraded to the HEST mattress, any long term review/feedback? Also what size did you go with for the Canopy Camper, Dually Long?
  6. ccperkdog

    SOLD - Leitner Designs ACS Forged Rack for 2020-2022 Jeep Gladiator

    Had a buyer ghost so the rack is available again as is the XPLOR fridge mount.
  7. ccperkdog

    Introducing the “NEW” Alu-Cab Canopy Camper

    I’ve seen one of these Aquor Water Systems detachable faucets set up on a Canopy Camper in place of the Alu-Cab water tank faucet. Also addresses potential freezing issues. https://www.aquorwatersystems.com/
  8. ccperkdog

    Introducing the “NEW” Alu-Cab Canopy Camper

    Thanks! It will be new. This thread is an invaluable resource.
  9. ccperkdog

    Jeep Gladiator Build Thread - 18 months around Australia with The Road Chose Me

    How is the Renogy system holding up as you trek all over Australia? Anything you would change?
  10. ccperkdog

    Introducing the “NEW” Alu-Cab Canopy Camper

    So I still have a few more weeks to wait before camper install and I have an electrical question. I have a GP Factor Basic electrical panel for the drivers side rear. Will I need to extend the factory wire harness for the camper to reach the drivers side or is there enough existing length? If...
  11. ccperkdog

    Introducing the “NEW” Alu-Cab Canopy Camper

    Did you get the RakAttach? Curious what it’s like for getting in and out of the Canopy Camper. Does it get in the way?
  12. ccperkdog

    Pronghorn bumper’s?

    One issue I saw was you could not mount a winch directly to the top, you needed their proprietary winch box, which was limited to specific models of winches. Chris switched back when he added a winch, and he also went back to the original stock bumper as a weight consideration. At least that is...
  13. ccperkdog

    Introducing the “NEW” Alu-Cab Canopy Camper

    1UP released a ver.2 of RakAttach that adapts both ways, so you don’t have to buy a passenger or drive side specific version
  14. ccperkdog

    Leitner Design Racks

    I’m currently in shipping queue for an ACS Forged and was considering using some webbing across the back in case any in-bed gear comes loose. Keeping the weight down.
  15. ccperkdog

    Goose Gear Cubbies? Yea or Nay?

    You can trim the plastic side panels with a dremel. Go slow, use tape, trim and test fit, trim again. I chose this route for cost and also I liked the look of just the full floor platform.
Top