Search results

  1. M

    Gen 1 FSM

    Hi all, I downloaded the FSM from Mitsubishilinks and in the heater A/C section all that is there is the heater section. Does anybody have the section that covers the A/C section for a Gen 1. I'm looking into rebuilding the system and want to have what the factory recommends as far as oil and...
  2. M

    Gen 1 A/C

    Hi all, does anybody have the portion of the FSM that covers the A/C? I only have the heater section when I downloaded the FSM. Thx in advance.
  3. M

    Transfer case switches

    Hi all, So on my gen 1, I have these 2 switches. One has 1 lead the other has 2 leads, when I look under all I see is 2 wires connecting to the switches. I figure the 1 wire broke, but I cant find the wire that broke. Would it be buried back in the wrap of the 2 wires that are still connected?
  4. M

    Wonky door locks

    Lately when I insert my key into the passenger door it unlocks all the doors but than all the doors lock back up except for the passenger door. Any ideas on where to start to trouble shoot?
  5. M

    Gen 1 A/C

    Morning all, I have a question about my A/C. It turns on, gets cold, idle bumps up when compressor turns on but the compressor does not turn off. The only way for me to turn off the A/C is to turn off the engine. I can hear (I think) the expansion valve under the dash when shutting off the...
  6. M

    Heater hoses

    I was wondering what has everyone done when heater hoses need to be replaced. I checked at the dealership and was quoted $80+ for the kit....Mitsubishi does not sell the hoses separately. I was worried that using just regular hoses would kink where it needs to be a 45. Is there an alternative...
  7. M

    Proportioning valve

    Hi all, as I'm getting ready to do the rear axle swap into my gen 1. For those who did the swap, did you need a proportioning valve for 4 wheel disc? I haven't seen any info except that everything just bolts up. Please help advise me on what's the best way for the 4 wheel disc set up on the gen...
  8. M

    Wiring for locker

    Hi all, I finally picked up a SR axle for my 91 and I'm gathering parts for the swap as well as reading how and what I need. But I have searched on how to wire a SR axle and I can't find any info. I understand power for the compressor, but am unsure on how to wire for the detent to indicate the...
  9. M

    Axle swap shopping list

    Hi all, so I'm leaning towards doing the SR axle swap and I want to have everything ready to go. So I know the obvious: SR rear axle trailing arms rear springs compressor Do I need anything for converting to 4 wheel disc? Proportioning valve? Locker switch? Any advice will be helpful at this...
  10. M

    SS brake lines

    Can anyone tell me if there is a SS brake lie kit for a Gen 1, or do you need to have one made. Thx for the input.
  11. M

    SR springs in a Gen 1

    I know its been done, but the other day I was going to install SR rear springs in but when I compared them side by side the SR springs were about 1''-1.5'' shorter than the originals. Is that right? Just wasn't sure, if it is I'll take another crack at it. Thx in advance.
  12. M

    Gen 1 fuel tank

    In replacing my sending unit on my 91 LWB, I noticed when I pulled it out it was pretty rusty. When I shined a light in the interior of the tank wasn't very cleaned. My question is are replacement tanks available? Has any one put in an aftermarket tank? Has anyone tried repairing the tank? I...
  13. M

    front diff

    I have a possibility of picking up a Starion lsd, I have a 91 LS 3.0 will that diff fit in mine? I've searched and I see post that the Starion diff will fit the 4 cylinder engine, but I wasn't sure if the all the front diffs were the same or different in the 3.0.
  14. M

    PCV valve question

    This might be a silly question, but I have rebuilt another 3.0, and it still smokes at idle. All new pistons, rings and valve seals. When I pulled apart the old motor it looked like something bounced around the cylinders, previous owner thought it died due to something in the valve train letting...
  15. M

    Aisin part numbers

    Aisin aftermarket list 2 different hubs, but shows the fit the same models. Can anyone tell me the difference between FHM-002 and FHM-003. Thx in advanced.
  16. M

    Manual hub question

    Hi all, Are all the hubs the same on a gen 1? Does it matter if its a 4 or 6 cylinder? I know the hub spline count is 28 on the 3.0. Reason being is that I was looking for manual hubs but a lot of the fitments list 82-87 and not compatible for the 91. Any feedback much appreciated, thx.
  17. M

    6g72 con rod bolts

    When disassembling the 6g72 and removing the pistons, do the con rods need to be replaced each time or can they be reused?
  18. M

    Rings not seating

    Hi all. I have installed a new motor in my 91, all went well fired right up. Drove it around the block lightly and it ran fine. But after awhile at idle it slowly died. It cranked like no compression, checked timing and all was good. I have squirted oil in each cylinder and it fired up and will...
  19. M

    Whats really needed for a full SR rear axle swap

    I have searched and all I find is the basic parts needed to make it work, but I want to know everything I need. What is the complete list of items needed? Besides an SR axle, dash switch and compressor what else should be taken from a donor vehicle? Is there a control box or relay that is...
Top