Search results

  1. bikerjosh

    1999 Jeep -Custom Cherokee-Comanche or pre-gladiator build

    Pretty cool take on an custom jeep. No affiliation w/seller https://omaha.craigslist.org/cto/d/dodge-jeep-cherokee-4door-flatbed/7136261244.html Jeep Cherokee 4door flatbed - $6500 image 1 of 7 © craigslist - Map data © OpenStreetMap 1999 jeep cherokee condition: excellent...
  2. bikerjosh

    What did you do to your Mitsubishi today?

    Skid plates on 93 L300, redoing ground cables.
  3. bikerjosh

    ** SOLD ** 2005 Sequoia Limited 4wd NorCal

    Craigslist link is broken
  4. bikerjosh

    2004 Tundra Adventure Cab - Build/Adventure Thread

    Yep x2, I called him up and in a short time ordered a bumper for my 06’ DC. He was pretty busy, so since I wasn’t in a rush picked it up 2 months later when I was passing through his area.
  5. bikerjosh

    WTB : OEM radio bracket for 1st gen (2006) Tundra

    Also, maybe crutchfield ?
  6. bikerjosh

    Searching for source of fuel injection fusible link, blowing.

    Maybe I'm missing something but Chapter/Section 90 the one with the electrical diagrams seems to be missing, reference ends at 80.
  7. bikerjosh

    Searching for source of fuel injection fusible link, blowing.

    @MarkGramlich , do you know where to get the electrical schematic for a 1998 Montero? I have both volumes of of the FSM, but neither have a full electrical schematic. thx
  8. bikerjosh

    Searching for source of fuel injection fusible link, blowing.

    Fuel Injection fusible link blowing? So while this happened a couple times over the last year and a half replacing the fusible link with a new 20amp would fix it. Today while running errands it blew again. Being about 5 miles from home and not having any links with me I pulled the 30A from...
  9. bikerjosh

    Diagram of what springs in valve body (trans)

    Thanks Toasty, yep have VB #1, think I figured out the spring order using calipers and some data online. Cracking the VB tomorrow morning once I get a strong cup of coffee in me. Pictures to follow. Thanks again
  10. bikerjosh

    Diagram of what springs in valve body (trans)

    Howdy Toasty, did you get a chance to ask Ernest? Also curious if he uses trans assembly grease to hold the accumulators up in the trans as you re-install the accumulators?
  11. bikerjosh

    Diagram of what springs in valve body (trans)

    1998 Montero 3.5 with AT. Anyone have a valve body diagram or list of the OEM spring colors that go in the accumulators above the valve body? When I was under the car removing the valve body, three accumulators (#2,3,4) fell out on to the ground scattering the springs. Waiting for the two...
  12. bikerjosh

    Best practices for removing trans pan Gen 2-2.5 Montero?

    BFH, and a paint scraper. PO or mechanic didn’t use a gasket just hightempRTV it appears.
  13. bikerjosh

    Best practices for removing trans pan Gen 2-2.5 Montero?

    I believe that thread is talking about the oil pan vs transmission pan?
  14. bikerjosh

    Best practices for removing trans pan Gen 2-2.5 Montero?

    Removed all the bolts including theb3 hidden by the cross member and yoke. Not a whole lot of area(s) where you can get a putty knife between the pan and trans to split the two. Tried tapping on the pan all around with a dead blow mallet but didn't do anything. Not sure if I should just put a...
  15. bikerjosh

    Tundra gen 1, single piece fender flare cutting.

    Port installed? Weird, yeah when I was communicating over the internet with the fabricator who built the bumper, kept asking me if I had aftermarket flares since he hadn't seen single piece ones.
  16. bikerjosh

    Tundra gen 1, single piece fender flare cutting.

    Howdy all I have an 06 4 door with oem single piece front flares as opposed to the two piece seen on most tundras. Replacing the bumper with steel plate and looking for advice on cutting flares, best tool to use and what if anything did you do to the cut edge of the flare that remains u channel...
  17. bikerjosh

    Roof rack lights wiring

    You just unhook the driver side and run the wires to the edge with some safety wire or fish tape. From the edge you can conceal them in the upper trim until you get to the front seat belt tower or continue them along the top until you get to the pillar at windshield them run them down.
  18. bikerjosh

    Roof rack lights wiring

    I ran mine through the mounts for the original roof rack. Assuming you aren't running the OEM rack, you can use one for the power supply into cab and the other for the ground. Josh
  19. bikerjosh

    2008 Land Rover LR3 Expedition Ready - Sold!

    Nice build out. Have a buddy with a stock LR3 HD (rear locker model) his only mod is AT tires, amazingly capable rig.
  20. bikerjosh

    2005 Armored 4wd Excursion Limo only 4k miles

    Wonder if the turning radius takes driver into another zip code? MPG, or GPM?
Top