Search results

  1. Toasty

    Anyone still make Gen1 skid plates?

    If you have no preference between aluminum or steel i'm guessing maybe you don't have even the stock skid plates?
  2. Toasty

    Gen 2 SR Engine Swap Options

    There is the Hyundai Santa Fe 3.5 DOHC, it's a licensed copy but i don't know anyone who has swapped one yet.
  3. Toasty

    Lunchbox Locker for ‘94 LS Montero?

    You're wanting a rear? Just buy an SR axle with an air locker, cheaper, easier and stronger. The fronts are available in a lunchbox variety.
  4. Toasty

    Gen 2 SR Engine Swap Options

    Diesel swap (correct engine for chassis (4M40) is much easier than a gas swap from a different platform, the diesel is a drop in for the most part and it needs minimal wiring for gauges and fuel cutoff. I recall 10ish wires. One could do a diesel swap in a day if he/she had all of the parts, the...
  5. Toasty

    Gen 2.5: Diamante engine swap?

    These engines are very different, unlike the Gen 1 3.0 and early Diamante 3.0 which are largely the same. The Diamante 3.5 would need everything swapped over, bosses tapped and distributor addressed (yes they still ran a dizzy). There are way easier swaps, late model Sports are plentiful and...
  6. Toasty

    Mitsubishi J53

    Email info@paladintrucks.com
  7. Toasty

    Found a Gen 1 Monty...what am I getting into...:)

    Use Partsouq.com and get superceded Gen 1 parts from the Hyundai Galloper like the window sash/mouldings, they're far better than stock and cheap. Marks4wd for transfer case gearing, the stock low range is dismal in these and with the 3.0 (especially with automatic) they really benefit from the...
  8. Toasty

    Would you bite? CL 1991 Pajero

    Blue interior is impossible to find, i'd hold out for a '94 model. They're better in every way plus they cost the same, that one is nice but you can get a way better machine for the same or less money. like PLH said, If you're not handy with a wrench or doing your own service i wouldn't...
  9. Toasty

    Post your Mitsubishi Pajero Pics

    I'd love to see pics of the double Mitsu transfer case, i've wanted to do that one myself. nice truck.
  10. Toasty

    Post your Mitsubishi Pajero Pics

  11. Toasty

    Is there a usdm vehicle that had a 4.9 low pinion 8" front diff?

    A lot of the 4.90 high pinion diffs don't have disconnects, they come from AWD Sports. As for 5.29's those come from the Hyundai Terracan and you can look them up on partsouq.com
  12. Toasty

    Is there a usdm vehicle that had a 4.9 low pinion 8" front diff?

    na3s is right, you are going to need to look for a 4.88 but you also might be able to just install a complete 4.90 axle assembly. I haven't put a high pinion in a Gen 1 though so i can't tell you for sure but you have both diffs already so some measuring would tell you for sure. I've put the low...
  13. Toasty

    Gen 2.5 grinding noise, HELP

    Clean it if possible and put a couple dabs of RTV on it to keep it from vibrating loose again and just tap it back until it's seated. If you want you can absolutely remove the drive shaft, the slip yoke just pulls out and a little gear oil will come with it (park nose downhill if possible).
  14. Toasty

    Gen 2.5 grinding noise, HELP

    That's the dust shield, you might be able to push it back in place without disconnecting anything otherwise yes the driveshaft needs to be removed to remove it.
  15. Toasty

    Gen 2.5 grinding noise, HELP

    Sounds like the transfer case damper, on the older trucks there all metal and they break. Later ones have a rubber isolated metal block, they're just for driveline noise reduction and you can take it off and drive without it to test.
  16. Toasty

    Can anyone school me in the 4m40 automatic?

    So, if you have the PCM that came from the 4M40 donor vehicle (assuming it wasn't scrapped in favor of the 4D56 ECU running the 4M40) you likely just need the harness branch to the V4A51 or V5A51 and Bob's your uncle. The mechanical diesel computers don't really care which engine they're running...
  17. Toasty

    Can anyone school me in the 4m40 automatic?

    I still think you have a Mitsu automatic, what is the vin number on the bottom of the block say? That will tell us what you've got and what the engine came out of
  18. Toasty

    UCA bushing removal video

    I know it's a terrible video but i hope it can help some of you guys, we'll get better at these. Maybe. I'll try to make the install video better 😅
  19. Toasty

    98 Gen 2.5 front LSD

    ^^^^ This is the route i'm going, the Starion diff up front isn't worth the effort (I ran one in my old '88). They're usually worn out and they don't work great to begin with.
  20. Toasty

    98 Gen 2.5 - Upgrade Inquiry - Seeking some advice

    https://www.4crawler.com/4x4/ForSale/BodyLiftKit.shtml Roger Brown makes some really nice body lifts, i have one on my truck. Several hardware options as well.
Top