Recent content by Shiryas

  1. S

    2018 Sprinter 4x4 144" Take 2

    Grant, Great build. Any idea where or what model these lights are? I looked on the first post and saw the LED puck lights but did not see these listed. Thanks, Chris Untitled by Grant Wilson, on Flickr
  2. S

    1997 Ford F350 CCLB 4x4 7.3 5sp $17,900 OBO

    SOLD SOLD SOLD 1997 Ford F350 CCLB 4x4 7.3 5sp $17,900 OBO Crew Cab Long Bed 7.3 Powerstroke Turbo Diesel 5speed Power windows Power locks Cruise control A/C Matching spare wheel and matching tire (new) Clean title in hand 172,000 miles Transmission was replaced at 157k with a fully rebuilt...
  3. S

    My latest Eurovan build "Snap Dragon"

    Cole, The color matched bedliner in this build and in your Sprinter looks great, do you do spray that or have a source in Ft Fun? Cheers, Chris
  4. S

    Project "Autonomous" F-350

    Papa, I have read your thread but I do not recall if you put anything where the spare tire used to go. On my 97 CCLB 7.3 I have two tanks, the forward one is 18 and the rear is 16. Like you I want a bit more fuel capacity and just picked up an Excursion 44 gallon tank which will fit in the rear...
  5. S

    Limited Slip Faceoff: Detroit TrueTrac vs. ARB Air Locker

    In the past I had ARB's on my 95 Toyota Pickup (XCab, 3.Slow, 5speed) and was happy with them but did have air line issues a couple of times. I have driven several Defenders and D1's with Detroits, which are great for off road but I could not live with their on road characteristics. When I did...
  6. S

    Project "Autonomous" F-350

    Pappawheely (Mike?), Nice looking rig and setup. I have a F350 crewcab as well but its the 7.3 and refreshing the steering is up next for my rig. I have found a lot of internet posts regarding the Saginaw pump from "possible" to "never going to clear the aluminum bracket", but have not seen...
  7. S

    Kelly Kettle, Aluminum Large Complete Kit $65 OBO

    SOLD SOLD SOLD I had bought this years ago before they were sold via a US distributor. It works great but I am shifting to motorcycle based trips and its just too big for that. They are going for $95 new: Located in...
  8. S

    OEM wheels for a 2013 F350

    P nut, The change point was 05 when they went to coils from leaf springs. So 05-13 is the correct metric bolt pattern, lug, and offset. My understanding from Cary at CT Performance is that in 09 they went to a slightly wider axle, ergo wider track width. I just happen to have a set in the...
  9. S

    Land Rover Holland & Holland Camp Stool

    Todd, Sorry about the delay, I was out of town. Email replied. Chris
  10. S

    Land Rover Holland & Holland Camp Stool

    SOLD SOLD SOLD I bought this when I worked at Land Rover, it was offered as and accessory for their Holland & Holland Range Rover (P38 platform). There are no mfg tags that I can locate and I have been unable to find any other information. My recollection from the Gear catalog was for a...
  11. S

    COLORADO-BLM Seeks Comments on Grand Junction Draft RMP/EIS

    The objections to these "surveys" and "coalitions" is that those of us living in Western Colorado have watched what has happened in Utah, lots of trail closures and reduced access for motorized hobbies and all that land that now has fewer users. One of the more popular places here in western...
  12. S

    Offroading paraplegic needed a lift.

    Awesome job BirdMad. Great idea, simple and effective.
  13. S

    Saudi Northern Expedition

    Lo2ay, Beautiful pictures. I grew up in Dhahran and was fortunate to have parents who liked to explore and they took us with them everywhere. Najran, the Rub-A-Khali, Asir, Madain Saleh, and so much more. Thanks for the trip down memory lane. The train and station were not restored when I was a...
  14. S

    Project MULE - Expedition build on a 1991 1500 4x4 Suburban

    PMA4x4, Nice Suburban build, the 'K' platform is all I grew up with overseas. On your site you show you are using a Toughbook CF29 in conjunction with your handheld GPS's. I have this model running Ubuntu currently and I have batted the idea of using the Tango software with it or just...