Recent content by CrewServed

Titan DIY 20gal wheel well water tank for sale. Free local delivery or meet up within 75 miles of Concord, CA 94520. $395 from TitanDIY and selling for $325. Item is brand new, just received this weekend but it ended up not fitting into layout. Shipping it back is pricey, so hoping there is...

NIB Thule Hideaway Awning. 8.5' length, rack mount. $950 obo. No mounting hardware included, but can include them for additional $100. We bought, installed on our van, deployed once, put it back and immediately removed it because it is not the right dimensions for our rig. We repackaged the...

How do you feel about a trade for a Fuji XT-1? Got a couple of lenses and some other accessories. PM if this tickles your fancy.

Alright, thanks guys. I've bookmarked the website and I'll go that route if/when parts start failing.

Looks like the exhaust is going to rust out from under the truck soon. I'll need to replace it in due time, so I'll start doing the homework now. Figuring an OEM replacement runs about $400, looks like an aftermarket option isn't a silly or unecessary upgrade. What are your experiences with...

Did a little wrapping up today since I ran out of daylight yesterday and had hit that point where workmanship takes a nosedive. https://youtu.be/YRSdQDRPshY I had previously installed an Anderson SB50 quick connect under the hood for my compressor. Turns out having to open the hood every time...

Installation Day! Not quite wrapped up with the job, but everything is in place and functioning as desired. In other words, my truck isn’t on fire. Center: RTMR with cover off Top right corner: Terminal block for positive source power to accessories. Right center: Bus bar for common...

Okay, parts came in, did some work, and almost ready to install. I had some Kydex lying around the garage from a previous project that had gotten my attention, so I made some measurements, cut the appropriate shape, and used a heat gun and the edge of my workbench to get the 90 degree bends I...

I have a confession to make: my current (hah!) wiring situation is disgraceful, which is one of the things that prompted this project. Really, the motivation to make it right is one of the driving factors, along with creating an opportunity to learn something new. I've been down in SoCal for...

Some shipments arrived and I had a couple of hours to spare to work on wiring. I'll be using these as jumpers to connect relays to positive bus. These harnesses will lead to a terminal block for both switched and un-switched circuits. I didn't want five spools of 10 AWG in different...

That's nice looking. Thanks for the idea! I've got some spare kydex sitting around the garage from a previous project that struck my fancy. I could cut you off some and send it your way. Save you a buck or two.

Yup, that’s the Dremel wheel I used. It kicked a lot of little flecks of plastic at my face. Eye protection for a solid win. I’m planning to cut away the inside of the console to give me clearance for jumpers and such. I’m thinking I’ll need to get some 90° quick disconnect terminals to...

SNITCHES GET SWITCHES. Or something like that. Anyway, the switches arrived. I ordered all these parts from OTRATTW.com. Switches are all single pole, single throw, which is what I needed as a simple on/off switch. Lower LED (green) is independent and will be tied in to my dash lights...

Heya Kevn - After I installed the new rack, the inadequacy of my old rack was very noticeable. Over the years the rack and had developed some play which I had learned to drive with. Since that change was incremental in nature, I didn't notice it until after the repair was made. I had previously...

I've been largely absent from this thread for quite some time. Haven't done a whole lot to the rig except to drive it all over creation and keep up with maintaining old and failing parts. I ran my Nitto Terra Grapplers down to the tread wear markers and replaced them with a complete set of the...