Recent content by bikerjosh

  1. bikerjosh

    1999 Jeep -Custom Cherokee-Comanche or pre-gladiator build

    Pretty cool take on an custom jeep. No affiliation w/seller https://omaha.craigslist.org/cto/d/dodge-jeep-cherokee-4door-flatbed/7136261244.html Jeep Cherokee 4door flatbed - $6500 image 1 of 7 © craigslist - Map data © OpenStreetMap 1999 jeep cherokee condition: excellent...
  2. bikerjosh

    What did you do to your Mitsubishi today?

    Skid plates on 93 L300, redoing ground cables.
  3. bikerjosh

    ** SOLD ** 2005 Sequoia Limited 4wd NorCal

    Craigslist link is broken
  4. bikerjosh

    2004 Tundra Adventure Cab - Build/Adventure Thread

    Yep x2, I called him up and in a short time ordered a bumper for my 06’ DC. He was pretty busy, so since I wasn’t in a rush picked it up 2 months later when I was passing through his area.
  5. bikerjosh

    WTB : OEM radio bracket for 1st gen (2006) Tundra

    Also, maybe crutchfield ?
  6. bikerjosh

    Searching for source of fuel injection fusible link, blowing.

    Maybe I'm missing something but Chapter/Section 90 the one with the electrical diagrams seems to be missing, reference ends at 80.
  7. bikerjosh

    Searching for source of fuel injection fusible link, blowing.

    @MarkGramlich , do you know where to get the electrical schematic for a 1998 Montero? I have both volumes of of the FSM, but neither have a full electrical schematic. thx
  8. bikerjosh

    Searching for source of fuel injection fusible link, blowing.

    Fuel Injection fusible link blowing? So while this happened a couple times over the last year and a half replacing the fusible link with a new 20amp would fix it. Today while running errands it blew again. Being about 5 miles from home and not having any links with me I pulled the 30A from...
  9. bikerjosh

    Diagram of what springs in valve body (trans)

    Thanks Toasty, yep have VB #1, think I figured out the spring order using calipers and some data online. Cracking the VB tomorrow morning once I get a strong cup of coffee in me. Pictures to follow. Thanks again
  10. bikerjosh

    Diagram of what springs in valve body (trans)

    Howdy Toasty, did you get a chance to ask Ernest? Also curious if he uses trans assembly grease to hold the accumulators up in the trans as you re-install the accumulators?
  11. bikerjosh

    Diagram of what springs in valve body (trans)

    1998 Montero 3.5 with AT. Anyone have a valve body diagram or list of the OEM spring colors that go in the accumulators above the valve body? When I was under the car removing the valve body, three accumulators (#2,3,4) fell out on to the ground scattering the springs. Waiting for the two...
  12. bikerjosh

    Best practices for removing trans pan Gen 2-2.5 Montero?

    BFH, and a paint scraper. PO or mechanic didn’t use a gasket just hightempRTV it appears.
  13. bikerjosh

    Best practices for removing trans pan Gen 2-2.5 Montero?

    I believe that thread is talking about the oil pan vs transmission pan?
  14. bikerjosh

    Best practices for removing trans pan Gen 2-2.5 Montero?

    Removed all the bolts including theb3 hidden by the cross member and yoke. Not a whole lot of area(s) where you can get a putty knife between the pan and trans to split the two. Tried tapping on the pan all around with a dead blow mallet but didn't do anything. Not sure if I should just put a...
  15. bikerjosh

    Tundra gen 1, single piece fender flare cutting.

    Port installed? Weird, yeah when I was communicating over the internet with the fabricator who built the bumper, kept asking me if I had aftermarket flares since he hadn't seen single piece ones.
Top