Hodakaguy's 4x4 Sprinter Build

Hodakaguy

Adventurer
Extending the drivers side wire chase board out a bit more to clear the wiring.

20200522_092148-X2.jpg


20200522_093444-X2.jpg


20200522_093524-X2.jpg


20200522_093647-X2.jpg


20200522_093653-X2.jpg



Now back up to Mike's at VanLab to get more panel work done.

20200522_161858-X2.jpg



Mike fitting panels and preparing to cover them in automotive tweed.

20200522_162313-X2.jpg


20200522_162325-X2.jpg


20200522_162406-X2.jpg


20200522_162530-X2.jpg


20200522_163224-X2.jpg


20200522_163305-X2.jpg


20200522_163312-X2.jpg


20200522_163327-X2.jpg



Mike hates being on camera so he used the router to whip up a "Home Improvement Wilson Fence Mask".....now he's ready to be in front of the camera lol.

20200522_163510-X2.jpg



Hodakaguy
 

Hodakaguy

Adventurer
Marine Grade Wire & Heat Shrink Terminals vs Automotive Grade.

In this video I highlight the differences between Marine grade wire & heat shrink crimp terminals vs standard automotive grade. I also cover the difference between standard crimping tools and specialized heat shrink crimp tools.

I use marine grade crimps and wire almost exclusively in all of my builds. This is the 3rd video in a series where I'm highlighting tools, materials and techniques I use while building out our vehicles.

Hope you find this information useful in your builds as well.


Titan Heat Shrink Crimp Tool - On Amazon here: CLICK HERE
Wirefy Heat Shrink Terminals - On Amazon here: CLICK HERE
Ancor Brand Duplex Marine Wire - On Amazon Here: CLICK HERE
Ancor Brand Primary Marine Wire - On Amazon Here: CLICK HERE
Split Wire Loom - On Amazon Here: CLICK HERE

Hodakaguy
 
Last edited:

Hodakaguy

Adventurer
Back up to VanLab today to work on Panels. Mike is cutting my panels with his CNC machine....they are fitting like a glove!

P5251037-X2.jpg


P5251038-X2.jpg


P5251039-X2.jpg



Getting ready to install one of the new JBL speakers in the rear panel. There will be 4 of these in the rear of the van.

P5251042-X2.jpg



And installed. One 1 of the 4 installed but the sound is a 100% improvement over the OEM units....it sounds great!

P5251088-X2.jpg


P5251090-X2.jpg


P5251087-X2.jpg


P5251084-X2.jpg



Mike fabricating panels....going to look great!

P5251044-X2.jpg


P5251049-X2.jpg


P5251053-X2.jpg


P5251057-X2.jpg


P5251060-X2.jpg



Not sure if Mike is trying to protect his lungs or maybe he just doesn't want to be on camera lol.

P5251065-X2.jpg


P5251071-X2.jpg


P5251075-X2.jpg



Looks sweet!

P5251078-X2.jpg


P5251079-X2.jpg


P5251081-X2.jpg


P5251091-X2.jpg



More to come....

Hodakaguy
 

Hodakaguy

Adventurer
Day started of with an Awesome thunder storm....and one of the most vibrant red sunrises I've ever seen. This photo is straight out of camera.

20200530_050216-X2.jpg



More panel progress....

Drivers side lowers built and installed.....Nice!

P5291094-X2.jpg


P5291099-X2.jpg


P5291100-X2.jpg


P5291101-X2.jpg



This will be the power feed for our portable Dometic Refrigerator.

P5291102-X2.jpg



Time to get the forward ceiling panel wired back up with lights :) Mike did a bang up job on the new panel, it looks great!

P5301109-X2.jpg



Feeding the wiring on the Genuine Marine lights back through the panel.

P5301111-X2.jpg


P5301112-X2.jpg



And trim ring back in place.

P5301114-X2.jpg



Installing the 3 way switches

P5301110-X2.jpg


P5301116-X2.jpg




P5301162-X2.jpg


P5301159-X2.jpg



Getting ready to wire up the switches and lights....again lol.

P5301165-X2.jpg



Wiring up the lights to the switch.

P5301167-X2.jpg


P5301181-X2.jpg



Continued Below....
 
Last edited:

Hodakaguy

Adventurer
Continued From Above...

I decided to use Flag style terminals (Available Here: CLICK HERE) this time around as the clearance behind the switch is limited with the insulation in place.

P5301185-X2.jpg


These style of crimp tools work good on Flag terminals

P5301186-X2.jpg



Some heat shrink added and the connection is ready to make up.

P5301176-X2.jpg


P5301183-X2.jpg



I also swapped out the ceiling wiring terminals over to Flag style for more clearance.

P5301192-X2.jpg



A flapper wheel made quick work on removing the sharp points sticking through the panel on the back side, don't need those wearing on wiring ect.

P5301203-X2.jpg


P5301205-X2.jpg



While I was prepping the Panel my buddy Mike at VanLab was trimming the B pillar plastic trim to fit with the new panels. Had to take a little material off the bottom edge to get the pillar to sit flush with the thicker than OEM panels. Fit's like a glove now!

P5301156-X2.jpg


P5301118-X2.jpg


P5301127-X2.jpg



Next up It's time to fabricate some tabs that will apply pressure to the back side of the ceiling panels and make sure they sit tight into the L-track. Some 1/8" x 2" Aluminum flat bar should do the trick.

P5301207-X2.jpg



Cut and Drilled...ready to install.

P5301210-X2.jpg



Tabs Pop riveted into place.

P5301216-X2.jpg



Some foam tape added to the ends of the pressure tabs to make a snug fit on the back side of the panels.

P5301226-X2.jpg



Wiring attached to the 3 way switch, panel is ready to be installed.

P5301230-X2.jpg



Anchoring the panel into place with screws, these screws will be hidden by the Maxxfan trim rings. Here I'm using a solder iron to seal the fabric where I'll be drilling the hole, sealing keeps the fabric from fraying over time.

P5301235-X2.jpg


P5301236-X2.jpg


P5301240-X2.jpg



Right on the money!

P5301262-X2.jpg


P5301265-X2.jpg



Continued Below....
 

Hodakaguy

Adventurer
Continued from above...

Now it's on to speaker installation and installing the power port for the fridge.

Here's the power port setup that I fabricated for the fridge power. There is a Blue Sea Marine cigarette plug on the top (Available Here: CLICK HERE) and a PowerLet port on the bottom. The PowerLet ports are great as they snap into place and won't vibrate loose going down rough roads etc. I always install a Powerlet port on the end of the fridge power cable for reliability. (Powerlet Ports Here: CLICK HERE)

P5301150-X2.jpg



Wired in and getting ready to screw into place.

P5301151-X2.jpg



I'm installing these JBL speakers in the new panels...they sound soooooo much better than the OEM units.

P5301144-X2.jpg



Speakers going in...

P5301187-X2.jpg


P5301196-X2.jpg



And installed. The fit and finish of the panels are great! If your looking for custom panels or cabinets Mike does great work!

P5301255-X2.jpg


P5301253-X2.jpg



The L-track stops short on the front for a tight fit against the B-pillar plastic.

P5301259-X2.jpg


P5301276-X2.jpg



Slider door panel curing and waiting to be installed.

P5301243-X2.jpg


P5301247-X2.jpg



With a severe thunder storm warning in effect and thunder not to far away we decided to call it a day and get both of our vans into the safety of Mike's shop for the night. More progress tomorrow.

P5301274-X2.jpg


P5301284-X2.jpg



More to come....

Hodakaguy
 

North

Observer
Nice write ups! Really enjoying following your progress.

What material are you/Mike using for fabric backer on the interior panels?
 

Stitebunny

Adventurer
Very nice work!
I also was curious about the foam and fabric you are using.
I appreciate the videos and always find something new to learn in them.
Maybe a video on making/finishing wall panels?!
 

Hodakaguy

Adventurer
Nice write ups! Really enjoying following your progress.

What material are you/Mike using for fabric backer on the interior panels?

Thanks Mate. The fabric is Automotive Tweed and the panels have closed cell foam between the fabric and plywood.

Hodakaguy
 

Hodakaguy

Adventurer
Very nice work!
I also was curious about the foam and fabric you are using.
I appreciate the videos and always find something new to learn in them.
Maybe a video on making/finishing wall panels?!

Thanks Mate. I have a few more video ideas...just need to get some time to make them up. The fabric is automotive grade Tweed with closed cell foam.

Hodakaguy
 

Hodakaguy

Adventurer
Rear ceiling panel is in!....

Fabricating the rear tension strips. These tabs will apply pressure to the bottom side of the ceiling panel and ensure a tight fit against the L-track.

P5311285-X2.jpg


P5311286-X2.jpg


P5311287-X2.jpg


P5311291-X2.jpg


P5311301-X2.jpg



Installing lights and switches in the rear panel. Using the solder gun again to melt the fabric where the screw holes are located, prevents the fabric from unraveling.

P5311306-X2.jpg



Installing the rubber bushings on the back side of the panel to protect the wires from chaffing

P5311310-X2.jpg


P5311313-X2.jpg



Wired Up.

P5311317-X2.jpg


P5311319-X2.jpg



Continued Below....
 

Hodakaguy

Adventurer
Continued from above....

Installing the tension tabs

P5311328-X2.jpg


P5311331-X2.jpg


P5311332-X2.jpg



Powered up...

P5311339-X2.jpg



Pinning the panel to the center braces.

P5311345-X2.jpg


P5311347-X2.jpg



These screws will be covered by the fans trim ring.

P5311349-X2.jpg



And installed. The fit up is really good!

P5311354-X2.jpg


P5311357-X2.jpg


P5311368-X2.jpg


P5311369-X2.jpg


P5311370-X2.jpg


P5311373-X2.jpg


P5311380-X2.jpg



These aluminum tabs are temporary supports for the panel to keep it from sagging, eventually the panel will be supported by the rear trim piece. The tabs are held in place with VHB tape for now.

P5311382-X2.jpg



Couple shots with the Fisheye Lens.

P5311386-X2.jpg


P5311386-X2.jpg


P5311391-X2.jpg



More to come....

Hodakaguy
 

Forum statistics

Threads
185,538
Messages
2,875,658
Members
224,922
Latest member
Randy Towles
Top