BeefCake's build...a roll your own Earthroamerish family expo rig

lostih

Observer
Finally got warm enough to paint the frame...
3f2eb68d82f51d7dbb316a7e3bf514fb.jpg
 

lostih

Observer
On the galvanized I used a self etching primer, on the bare steel a shop coat primer from Forrest Industrial coatings and top coat of Good old rustoleum satin black. Hope it all cures up ok!
 

lostih

Observer
Well I set the frame on the back today...

I think I’m ok with the length, but looking forward to getting the box on it to see how it looks. I’m hoping to build an at least temporary direct mount system so that I can drive it up the same off camber hill and see how much it stiffens the frame. I go back and forth on how much it will help and figure there’s only one way to find out. I’d like to avoid a torsional mount if I can.

a59c29e0f25248681b60661611c54b43.jpg


37f56e3ca4e37573144d30c383ae5415.jpg


1ba90e4a23fada0e25f99f8c3af806be.jpg
 

heimbig

OnTheRoadAtLast
Looking good! You might be a bit longer than my GOVE f550 build. keeping mass forward will help because you could end up with rear of the truck causing some nasty swinging. And those tires will be great off road but they allow a lot of movement from side to side when you are at freeway speeds.
 

lostih

Observer
Have you checked for up-travel clearance, when flexed and stuffed?

That looks pretty tight.

Not yet. Hoping to do that with the temp mounts soon. I have about 6” up travel at the moment which I think is sufficient so if I need to limit it I will. If I do a three point mount it will add a couple inches as well.
 

lostih

Observer
Well...making some progress. I worked on the front of the camper where the over cab bed area will attach. I recycled some of the aluminum framing I cut out from other places and added capped off the walls for a better fastening spot. I’m using sikaflex 252 and the 206 primer and aktivator.

Here’s the wall as cut:
d7fefb1d3ea0737f8ae2d6ae3101ee22.jpg


Here it is with some foam removed and the new aluminum being slid in
c3fd4943534cce9431e07fda4d110986.jpg


While I wouldn’t recommend many of the construction techniques I see in rv construction I thought this was a good idea...
0948a101247f7773b9ec995b4f7ddea9.jpg


It looks like in high stress area the manufacturer puts thin gauge sheet in the lamination process. Kinda cool. Since I’m recycling the walls I couldn’t add these where they are needed...but I will if I ever build one from scratch.
 

lostih

Observer
89e26a0adcc778121f676b792dee5d12.jpg


Here’s the primer painted on the aluminum pieces.
44ecf7cce03f6d4753bd23a05849ab0e.jpg


I didn’t take any pics of this but I should have taped the edges on the camper where I wanted it. I got a bit carried away and had a bunch of cleanup to do to get the primer off where I didn’t want it.

Next up was gluing the filon material to my sandwich panels. They make a special contact cement for filon that I bought from the rv place. I ended up spraying it on using a harbor freight hvlp gun. Not sure what it’s supposed to look like but they seemed to adhere really well.

41f8152f1b8c7736d30eaa11851322b2.jpg


bde0685311420011672a6e28deadee6e.jpg


First panel done:
8069a30e86c0bb80f320175ff6505d72.jpg


The filon comes with a clear protective film on the finished side. This is great as you don’t have to be as careful to keep it clean or free of contact cement.
 

lostih

Observer
Everything was going great until this happened...

337511ca37ceb446001666144ccd709b.jpg


That’s what happens when your air hose gets wrapped around your gallon can of $100 contact cement and flops it over. Ew.

Hope the Cummins has enough oomph to get the tire of the shop floor
 

Forum statistics

Threads
185,530
Messages
2,875,576
Members
224,922
Latest member
Randy Towles
Top